KE811CT(w-type)CAT5 SWITCHERVer 1.0EInstruction ManualThank you for your purchase of this productPlease be sure to read this manual completely prior t
⑦ CAT5_OUT button CAT5 output is selected. ⑧ Front Dip Switch Please refer to "4-1. The setting of front dip switch." ⑨ SERIAL_3
⑫ ⑬ ⑯ ⑲ ⑳⑰ ⑱⑭ ⑮212221AUDIO IN1COMPOSITE IN233 COMPOSITE SUB OUTRGB IN6545677AUDIO SUB OUTCOMPONENT INSERIAL 1RGB SUB OUTSERIAL 2CAT5 OUT2CAT5 OUT1ABC
⑳ FG The screw for frame ground. AUDIO IN 1-4 RCA connector for audio input connector. These connectors are audio input co
3. Connection 3-1.The cautions and warnings ◆Cautions ・ Use the recommended a twisted-pair cable for this product for best results. (OKANO
12345678123456781,2…pair 13,6…pair 24,5…pair 37,8…pair 4ConnectorCablesConnector3-2.Preparation of a cable A CAT5e or CA
Cable mounting kitCable mounting kitCable mounting kitRack mounting kit 3-3. Cable mounting kit and rack mounting kit A mounting kit for the t
3-4. How to connect Connect this product according to the following procedures. Ⅰ.Check that all of the devices ,PDP(Plasma Display Panel), vi
input Linput Rinput Linput Rinput Linput Rinput Linput Routput Loutput RConnectorConnector21AUDIO IN345 6 7Mini-jack for audio input(
1 2 3 4ONGH4. Operation 4-1. The setting of front dip switch NO. 1 ON :Registration mode (Regardless of the setting of No.2-4.)
1 2 3 4 5 6 7 8OFF4-2. The setting of bottom dip switch NO. 1 ON :OPTION A button, momentary OFF:OPTION A button, alternate
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Thes
4-3. Operation of buttons a) POWER CONT button It can control the power in the rack. The operation of others buttons can be controll
5. Serial interface 5-1. The setting of personal computer Set the personal computer as follows, when this product is controlled. Baud rate
5-2. Connection of RS232C cablePin1 Non connect (NC)Pin2 Transmitted (TX)Pin3 Received Data (RD)Pin4 DTE ready connected with Pin6.Pin5 GND
Command Character ASCII noteIN1 A 41H IN2 B 42H IN3 C 43H IN4 D 44H IN5 E 45H IN6 F 46H IN7 G 47H IN8 H 48H DISPLAY_POWER I 49H POWER_CONT J
-18-※ When OPTION button is used as alternate, control command can transmit ON/OFF registration command. When OPTION button is used as momentary,
a) When controlling this product by sending one control command. This product can be controlled. Please send control command in the following o
-20-b) When controlling this product by sending control command consecutively. This product can be controlled. 8 control commands can be sent co
c) Reading data To read the data, the current state of this product can be understood.Sending1. Character (reading data command)2. ReturnReceiving1
connecter-pin Signal Input or Output1 POWER_CONT OUT2DISPLAY_POWEROUT3 OPTION_A OUT4 OPTION_B OUT5OPTION_C OUT6OPTION_D OUT7OPTION_E OUT8OP
Video :RGB4system、Component1system、Composite:3system、Audio:8system Video:SUB output(RGB/component、composite)each1system、Output for extension1system(2
Usage CautionsPlease be sure to read this manual prior to usage of product. After reading, keep it in a place near the equipment where it can be easil
-24-7-2. The specification of control system connectors 7-2-1.Contact output connectors for power control (POWER CONT) and option (OPTION A-F)
-25-(Ex.) When putting LED (forward voltage 2V), maximum current is I= ≦20mA ,and then R≧50Ω . 5-2 R+100+5VR(≧50Ω)(Connection equipment
7-2-3. Connector for parallel input Connector pin No. 31-49 for input Connector pin No. 21-25 GND Connector pin No
8.Trouble shooting-27-ProblemPlease check the followingReferenceThe video can't beseenThe video is flickering or thereis noise● Is the power of t
-28-Sound has noise● Is the twisted pair cable near the AC line? It should be far from the line.● Is there a source causing noise close to AC ad
※ Design and specifications are subject to change without notice.2006.4.14B&
◆Do not continue to use this product if any of the following occurs : ※It may cause fire or electric shock. ・If you smell a strange odor or smoke.
◆Do not disconnect or connect the power plug with wet hands. ※May cause electric shock.◆Do not put this product in the following places. ※May cause
3. Connection3-1. The cautions and warnings3-2. Preparation of a cable2-1. Front panel 2. The name and function of each parts 4. Operation4-2. The set
Fixing bands×2Cable mounting kitRack mounting kit ×2Screw×4Screw×4Instruction Manual (This booklet)Main unit of KE811CT(w-type)KE811CT(w-type)CAT5 S
Name of signal Transmission distanceAudio signal/serial data :10∼300m(32.8∼984.2ft)Composite signal :10∼300m(32.8∼984.2ft)YPbPr/YCbCr :10∼3
-3-⑤① ② ③ ④ ⑦ ⑭⑤ ⑥RGB IN8SERIAL 3AUDIO IN814SUB OUTCAT5 OUTOFF87654321INPUT FOPTIONEDBA CDISPLAYPOWERCONTPOWERKE811CT⑪⑧⑨22⑩2. The name and function of
Kommentare zu diesen Handbüchern